View GL600USB-A_379623.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Genesys Logic, Inc.
GL600USB GL600USB-A GL600USB-B USB MOUSE MICROCONTROLLER
SPECIFICATION 1.3 Jun 19, 2000
Genesys Logic, Inc. 10F, No.11, Ln.3, Tsao Ti Wei, Shenkeng, Taipei, Taiwan Tel: 886-2-2664-6655 Fax: 886-2-2664-5757 http://www.genesyslogic.com
GL600USB/GL600USB-A/GL600USB-B TABLE OF CONTENTS
TABLE OF CONTENTS .............................................................................................................................................1 TABLE OF CONTENTS .............................................................................................................................................2 TABLE OF FIGURES .................................................................................................................................................3 1 2 3 FEATURES ............................................................................................................................................................4 FUNCTIONAL OVERVIEW ...........................................................................................................................5 PIN DEFINITIONS AND DESCRIPTIONS ................................................................................................6 3.1 3.2 3.3 4 GL600USB ......................................................................................................................................................6 GL600USB-A ..................................................................................................................................................8 GL600USB-B ..................................................................................................................................................9
FUNCTIONAL DESCRIPTION....................................................................................................................10 4.1 MEMORY ORGANIZATION ......................................................................................................................10 4.1.1 Program Memory Organization ................................................................................................... 10 4.1.2 Data Memory Organization........................................................................................................... 10 4.2 4.3 4.4 4.5 4.6 USB FUNCTION REGISTERS ..................................................................................................................11 MCU FUNCTION REGISTERS ................................................................................................................14 FULL-RANGE DETECTION AND ANALOG-TO-DIGITAL CONVERTER.....................................18 GENERAL PURPOSE I/O PORTS ...........................................................................................................19 TIMER INTERRUPT ...................................................................................................................................19
4.7 USB ENGINE................................................................................................................................................19 4.7.1 Voltage Regulator ............................................................................................................................. 19 4.7.2 USB Transceiver................................................................................................................................ 20 4.7.3 Serial Interface Engine (SIE) ......................................................................................................... 22 4.8 INSTRUCTION SET SUMMARY ..............................................................................................................22 4.8.1 Operand Field Descriptions ........................................................................................................... 22 4.8.2 Instruction Set.................................................................................................................................... 22 5 6 7 ABSOLUTE MAXIMUM RATINGS ...........................................................................................................31 ELECTRICAL CHARACTERISTICS ........................................................................................................31 PACKAGE DIAGRAMS ..................................................................................................................................33 7.1 7.2 16-pin P-DIP..............................................................................................Error! Bookmark not defined. 18-pin P-DIP..............................................................................................Error! Bookmark not defined.
2
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
7.3 7.4 7.5 7.6 20-pin P-DIP..............................................................................................Error! Bookmark not defined. 16-pin SOP.................................................................................................Error! Bookmark not defined. 18-pin SOP....................................................................................................................................................37 20-pin SOP....................................................................................................................................................38
TABLE OF FIGURES Figure 2-1 Block Diagram of GL600USB.......................................................................... 5 Figure 3-1 20-pin DIP (GL600USB) .................................................................................. 7 Figure 3-2 18-pin DIP (GL600USB-A).............................................................................. 8 Figure 3-3 16-pin DIP (GL600USB-B) .............................................................................. 9 Figure 4-1 Program Memory Space.................................................................................. 10 Figure 4-2 Data Memory Space ........................................................................................ 11 Figure 4-3 Differential Input Sensitivity over Entire Common Mode Range .................. 20 Figure 4-4 Receiver Jitter Tolerance................................................................................. 21 Figure 4-5 Data Signal Rise and Fall Time ...................................................................... 22 Figure 7-1 Package outline dimension for 16-pin P-DIP.....Error! Bookmark not defined. Figure 7-2 Package outline dimension for 18-pin P-DIP.....Error! Bookmark not defined. Figure 7-3 Package outline dimension for 20-pin P-DIP.....Error! Bookmark not defined. Figure 7-4 Package outline dimension for 16-pin SOP .................................................... 36 Figure 7-5 Package outline dimension for 18-pin SOP .................................................... 37 Figure 7-6 Package outline dimension for 20-pin SOP .................................................... 38
3
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
1
FEATURES
Low-cost solution for low-speed USB mouse 8-bit micro-controller - Operation Speed: DC to 6MHz clock input - Performance: 3 MIPS @ 6MHz - Single cycle instruction execution - RISC-like architecture - USB optimized instruction set USB Specification Compliance - Conforms to USB 1.5Mbps Specification, Version 1.1 - Conforms to USB HID Class Specification, Version 1.1 - Supports 1 device address and 2 endpoints (include endpoint 0) I/O ports - Up to 13(GL600USB)/11(GL600USB-A)/9(GL600USB-B) general purpose I/O pins (OTP type is less a GPIO pin than mask type) - Internal RC clock to wakeup periodically (about 500ms) when suspend - Up to 8(GL600USB)/6(GL600USB-A)/4(GL600USB-B) special purpose I/O pins optimized for photo-sensor (Internal build in 4 bits ADC) - Up to 2 I/O pins with large current drive capability to drive LED (Sink current up to 16 mA) Internal memory - 64 bytes of RAM (special purpose register is not included) - 1.75K x 14 of program ROM Integrated USB transceiver Patented full-range detection for photo-sensor - Removes the expensive process of matching LED and photo-sensor On-chip 3.3v output - No external regulator required Improved output drivers with slew-rate control to reduce EMI 6 MHz external clock Internal power-on reset(POR) Internal power-fail detector Supports suspend/normal mode power management - Suspend current lower than 400A for whole mouse system (mask type) 8-bits free-running timer Available in cost saving 20-pin(GL600USB) PDIP, 18-pin(GL600USB-A) PDIP and 16pin(GL600USB-B) PDIP
* *
* *
* * * * * * * * * * *
4
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
2
FUNCTIONAL OVERVIEW
The GL600USB is a 8-bits RISC-like high performance microcontroller with a built-in 1.5Mbps SIE and transceiver. The microcontroller features 33 instructions optimized for USB applications. There are 64 bytes on-chip RAM and 1.75K x 14 program ROM incorporated into the microcontroller. The GL600USB accepts a 6MHz ceramic resonator or a crystal as its clock source. The microcontroller features 12 general purpose I/Os (GPIOs). 8 GPIO pins build in 4 bits ADC for photo-sensor input to remove the expensive process of matching LED and photo-sensor. Additionally, 2 GPIO pins are strong enough to drive LEDs. All GPIO ports feature low EMI emissions as a result of improved output drivers with slew-rate control.
USB Registers & FIFO Control
Microcontroller
Endpoint 0 8 Bytes FIFO D+ USB Interface DEndpoint 1 8 Bytes FIFO
Figure 2-1 Block Diagram of GL600USB
5
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
3
3.1
PIN DEFINITIONS AND DESCRIPTIONS
GL600USB Pin No. 1 Name P1.2/LB[1] I/O I/O
Description Port 1 bit 2/mouse left button Internal pull up 10K 2 P1.3/MB I/O Port 1 bit 3/mouse middle button Internal pull up 10K 3 P1.4/RB I/O Port 1 bit 4/mouse right button Internal pull up 10K 4 P2.7/W2 I/O Port 2 bit 7/photo-sensor input for horizontal scroll 2 Optional internal pull down from 4K ~ 32K or no pull down resistor 5 VCC Voltage supply 6 XTAL2 O Ceramic resonator or crystal out 7 XTAL1 I Ceramic resonator or crystal in 8 P2.4/Z1 I/O Port 2 bit 4/photo-sensor input for vertical scroll 1 Optional internal pull down from 4K ~ 32K or no pull down resistor 9 D+ I/O USB data+ 10 DI/O USB data11 V3.3 O 3.3V output, a 0.1uF to 1uF capacitor should be added on external circuit for this pin 12 P2.5/Z2 I/O Port 2 bit 5/photo-sensor input for vertical scroll 2 Optional internal pull down from 4K ~ 32K or no pull down resistor 13 P2.6/W1 I/O Port 2 bit 6/photo-sensor input for horizontal scroll 1 Optional internal pull down from 4K ~ 32K or no pull down resistor 14 P1.0 I/O Port 1 bit 0 with LED drive capability 15 P1.1 I/O Port 1 bit 1 with LED drive capability 16 GND Ground 17 P2.3/Y1 I/O Port 2 bit 3/photo-sensor input for Y axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor 18 P2.2/Y2 I/O Port 2 bit 2/photo-sensor input for Y axis 2 Optional internal pull down from 4K ~ 32K or no pull down resistor 19 P2.1/X1 I/O Port 2 bit 1/photo-sensor input for X axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor 20 P2.0/X2 I/O Port 2 bit 0/photo-sensor input for X axis 2 Optional internal pull down from 4K ~ 32K or no pull down resistor Note 1: Name or description after "/" means default function specified by Genesys Logic firmware Table 3-1 GL600USB Pin Definitions and Descriptions
6
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
P1.2 P1.3 P1.4 P2.7 VCC XTAL2 XTAL1 P2.4 D+ D-
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
P2.0 P2.1 P2.2 P2.3 GND P1.1 P1.0 P2.6 P2.5 V3.3
Figure 3-1 20-pin DIP & SOP (GL600USB)
7
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
3.2 GL600USB-A Pin No. 1 2 3 4 5 6 7 Description Port 1 bit 2/mouse left button Internal pull up 10K P1.3/MB I/O Port 1 bit 3/mouse middle button Internal pull up 10K P1.4/RB I/O Port 1 bit 4/mouse right button Internal pull up 10K VCC Voltage supply XTAL2 O Ceramic resonator or crystal out XTAL1 I Ceramic resonator or crystal in P2.4/Z1 I/O Port 2 bit 4/photo-sensor input for vertical scroll 1 Optional internal pull down from 4K ~ 32K or no pull down resistor D+ I/O USB data+ DI/O USB dataV3.3 O 3.3V output, a 0.1uF to 1uF capacitor should be added on external circuit for this pin P2.5/Z2 I/O Port 2 bit 5/photo-sensor input for vertical scroll 2 Optional internal pull down from 4K ~ 32K or no pull down resistor P1.0 I/O Port 1 bit 0 with LED drive capability P1.1 I/O Port 1 bit 1 with LED drive capability GND Ground P2.3/Y1 I/O Port 2 bit 3/photo-sensor input for Y axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor P2.2/Y2 I/O Port 2 bit 2/photo-sensor input for Y axis 2 Optional internal pull down from 4K ~ 32K or no pull down resistor P2.1/X1 I/O Port 2 bit 1/photo-sensor input for X axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor P2.0/X2 I/O Port 2 bit 0/photo-sensor input for X axis 2 Optional internal pull down from 4K ~ 32K or no pull down resistor Table 3-2 GL600USB-A Pin Definitions and Descriptions Name P1.2/LB[1] I/O I/O
8 9 10 11
12 13 14 15
16
17
18
P1.2 P1.3 P1.4 VCC XTAL2 XTAL1 P2.4 D+ D-
1 2 3 4 5 6 7 8 9
18 17 16 15 14 13 12 11 10
P2.0 P2.1 P2.2 P2.3 GND P1.1 P1.0 P2.5 V3.3
Figure 3-2 18-pin DIP & SOP (GL600USB-A)
8
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
3.3 GL600USB-B Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Name P1.2/LB[1] P1.3/MB P1.4/RB VCC XTAL2 XTAL1 D+ DV3.3 P1.0 P1.1 GND P2.3/Y1 Description Port 1 bit 2/mouse left button Internal pull up 10K I/O Port 1 bit 3/mouse middle button Internal pull up 10K I/O Port 1 bit 4/mouse right button Internal pull up 10K Voltage supply O Ceramic resonator or crystal out I Ceramic resonator or crystal in I/O USB data+ I/O USB dataO 3.3V output, a 0.1uF to 1uF capacitor should be added on external circuit for this pin I/O Port 1 bit 0 with LED drive capability I/O Port 1 bit 1 with LED drive capability Ground I/O Port 2 bit 1/photo-sensor input for X axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor I/O Port 2 bit 1/photo-sensor input for X axis 2 Optional internal pull down from 4K ~ 32K or no pull down resistor I/O Port 2 bit 2/photo-sensor input for Y axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor I/O Port 2 bit 3/photo-sensor input for Y axis 1 Optional internal pull down from 4K ~ 32K or no pull down resistor Table 3-3 GL600USB-B Pin Definitions and Descriptions I/O I/O
14
P2.2/Y2
15
P2.1/X1
16
P2.0/X2
P1.2 P1.3 P1.4 VCC XTAL2 XTAL1 D+ D-
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
P2.0 P2.1 P2.2 P2.3 GND P1.1 P1.0 V3.3
Figure 3-3 16-pin DIP & SOP (GL600USB-B)
9
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
4
FUNCTIONAL DESCRIPTION
The Genesys Logic GL600USB microcontroller is optimized for USB 2D/3D/4D mouse. This USB microcontroller conforms to the low-speed (1.5Mbps) requirements of the USB Specification version 1.1. The microcontroller is a self-contained unit with an USB SIE, an USB transceiver, an 8-bits RISC-like microcontroller, a timer, data and program memories. It supports one USB device address and two endpoints (include endpoint 0). 4.1 MEMORY ORGANIZATION
The memory in the microcontroller is organized into user program memory in program ROM and data memory in SRAM space. 4.1.1 Program Memory Organization
The 11-bit Program Counter (PC) is capable of addressing 2K x 14 of program space. However, the program space of the GL600USB is 1.75K x 14. The program memory space is divided into two functional groups: Interrupt Vectors and program code. After a reset, the Program Counter points to location zero of the program space. After a timer interrupt, the Program Counter points the location 0x0004 of the program space.
After Reset
Address 0x0000
Reset Vector
After Timer Interrupt
0x0004 0x0005
Timer Interrupt Vector
1.75K x 14 ROM 0x06FF Figure 4-1 Program Memory Space 4.1.2 Data Memory Organization
The data memory is partitioned into two banks which contain the General Purpose Registers, MCU Function Registers and USB Function Registers. Bit RP0 is the bank select bit. RP0 (STATUS<5>) = 1 Bank 1 RP0 (STATUS<5>) = 0 Bank 0 The lower locations of each Bank are reserved for MCU Function Registers and USB Function Registers. Above the MCU Function Registers and USB Function Registers are General Purpose Registers implemented as SRAM. Both Bank 0 and Bank 1 contain MCU Function Registers. USB Function Registers are located in Bank 0. Some "high use" MCU Function Registers from Bank 0 are mirrored in Bank 1 for code reduction and quicker access. Data Memory Address 00h 01h Data Memory Address 80h 81h
INDR TIMER
INDR PSCON
10
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Fh 20h General Purpose Registers (64 bytes) 5Fh 60h PCL STATUS INDAR PORT1 PORT2 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h PCL STATUS INDAR PORT1CON PORT2CON
PCHBUF INTEN PHVAL PHSEL DMODE DEVCTL EVTFLG DEVADR FFCNT0 FFCNT1 FFCTL FFDAT0 FFDAT1 EP0RXST
PCHBUF INTEN
7Fh
FFh Bank 0 Figure 4-2 Data Memory Space
Bank 1
4.2
USB FUNCTION REGISTERS Name DEVCTL EVTFLG DEVADR FFCNT0 FFCNT1 FFCTL Function Device control register Event flag register USB device address register Byte count buffer for endpoint 0 Byte count buffer for endpoint 1 FIFO control register
Address 10h 12h 13h 14h 15h 16h
11
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
17h 18h 19h FFDAT0 FFDAT1 EP0RXST Endpoint 0 FIFO port Endpoint 1 FIFO port Endpoint 0 receiving status register Table 4-1 USB Function Register Summary
DEVCTL (Address 10h, Device control register) R/W[1] R/W R/W R/W R/W R/W TXSE0 EP0STL EP1STL WAKE WKDIS PWRDN TXSE0: Set and clear transmitting SE0 bit 1: Set transmitting SE0 0: Clear transmitting SE0 EP0STL: Endpoint 0 stall bit. This bit will be cleared automatically by hardware when SETUP packet is received 1: Endpoint 0 will respond with a STALL to a valid transaction except SETUP 0: Endpoint 0 will not respond with a STALL to a valid transaction EP1STL: Endpoint 1 stall bit 1: Endpoint 1 will respond with a STALL to a valid IN transaction 0: Endpoint 1 will not respond with a STALL to a valid IN transaction WAKE: Wake-up bit 1: Set this bit to wake up host controller by placing USB bus into K state 0: Clear this bit to force USB bus leave K state WKDIS: Wake-up disable bit. The WAKE bit has no effect if WKDIS bit is set to 1. 1: Disable remote wake-up capability 0: Enable remote wake-up capability PWRDN: Power-down mode bit. Writing 1 to this bit will enter power-down mode If USB suspend is detected, firmware can set this bit to enter power-down mode. In power-down mode, crystal/resonator will stop. The PWRDN bit will be cleared automatically by hardware and crystal/resonator will restart when the internal RC timer timeout (about 500ms). Firmware should check buttons and photo position encoders of the mouse. If mouse status is not changed, Firmware should set the PWRDN bit to enter power down mode again. Power consumption in suspend mode depends on how much time the firmware checking mouse status changed. Hardware will also clear PWRDN bit automatically when USB D+ or D- is toggled. 0: Normal mode, not power-down Value on POR: "1 - 0 - 0 0 0 0" [2] Note 1: "R/W" means readable and writable bit. All reserved fields should not be changed by firmware. Note 2: "-" means unimplemented read as 0 EVTFLG (Address 12h, Event flag register) R/W1C[1] R/W1C RESUME SUSPD RESUME: Global resume bit 1: Global resume (USB D+/D- toggle) was detected 0: Global resume was not detected SUSPD: Global suspend bit 1: Global suspend (USB idle more than 3ms) was detected 0: Global suspend was not detected EP1TX: Endpoint 1 transmitting status bit 1: Data has been sent from endpoint 1 0: Data has not been sent from endpoint 1 EP0TX: Endpoint 0 transmitting status bit 1: Data has been sent from endpoint 0 0: Data has not been sent from endpoint 0 EP0RX: Endpoint 0 receiving status bit
R/W1C EP1TX
R/W1C EP0TX
R/W1C EP0RX
12
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
1: Data has been received by endpoint 0 0: Data has not been received by endpoint 0 Value on POR: "- - - 0 0 0 0 0" Note 1: "R/W1C" means read-only and write "1" to clear bit DEVADR (Address 13h, USB device address register) R/W R/W R/W DADR6 DADR5 DADR4 Write this register to set the USB device address Value on POR: "- 0 0 0 0 0 0 0"
R/W DADR3
R/W DADR2
R/W DADR1
R/W DADR0
FFCNT0 (Address 14h, Byte count buffer for endpoint 0) R/O[1] R/O R/O R/O R/W R/W RXCNT3 RXCNT2 RXCNT1 RXCNT0 TXCNT3 TXCNT2 RXCNT[3:0]: Number of bytes received by endpoint 0 OUT transaction TXCNT[3:0]: Number of bytes to be sent by endpoint 0 IN transaction Value on POR: "x x x x x x x x" Note 1: "R/O" means read-only bit. Writing this bit is no effect. FFCNT1 (Address 15h, Byte count buffer for endpoint 1) R/W R/W TXCNT3 TXCNT2 TXCNT[3:0]: Number of bytes to be sent by endpoint 1 IN transaction Value on POR: "- - - - x x x x"
R/W TXCNT1
R/W TXCNT0
R/W TXCNT1
R/W TXCNT0
FFCTL (Address 16h, FIFO control register) W/O[1] R/W R/W R/W W/O R/W R/W FFRST1 TXSEQ1 TXOE1 RXDIS0 FFRST0 TXSEQ0 TXOE0 FFRST1: Reset endpoint 1 FIFO read/write pointer Write "1" to this bit will reset endpoint 1 FIFO read/write pointer. Data in endpoint 1 FIFO remain unchanged. Before data are written into endpoint 1 FIFO, FFRST1 should be written first. TXSEQ1: Endpoint 1 transmitting data sequence bit 1: Transmitting data use DATA1 as PID 0: Transmitting data use DATA0 as PID TXOE1: Endpoint 1 FIFO data ready bit 1: Endpoint 1 FIFO data are ready to be transmitted. Data will be transmitted when a valid IN token is received. This bit is automatically cleared by hardware after the transaction complete (ACK is received). 0: Endpoint 1 FIFO data are not ready to be transmitted. Endpoint 1 will respond with a NAK to a valid IN transaction. RXDIS0: Endpoint 0 receiving not available bit 1: Endpoint 0 FIFO is not available. The received data cannot be pushed into FIFO. The USB controller will respond with a NAK to a valid OUT transaction. This bit is set by hardware when endpoint 0 data is received (both SETUP and OUT transaction) and should be cleared by firmware after data is read from FIFO. 0: Endpoint 0 FIFO is available for data receiving FFRST0: Reset endpoint 0 FIFO read/write pointer Write "1" to this bit will reset endpoint 0 FIFO read/write pointer. Data in endpoint 0 FIFO remain unchanged. Before data are written into endpoint 0 FIFO, FFRST0 should be written first. TXSEQ0: Endpoint 0 transmitting data sequence bit 1: Transmitting data use DATA1 as PID 0: Transmitting data use DATA0 as PID TXOE0: Endpoint 0 FIFO data ready bit
13
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
1: Endpoint 0 FIFO data are ready to be transmitted. Data will be transmitted when a valid IN token is received. This bit is automatically cleared by hardware after the transaction complete (ACK is received). 0: Endpoint 0 FIFO data are not ready to be transmitted and respond with a NAK to a valid IN transaction. Value on POR: "- 0 0 0 0 0 0 0" Note 1: "W/O" means write-only bit. 0 will be returned when reading this bit FFDAT0 (Address 17h, Endpoint 0 FIFO port) R/W R/W R/W R/W R/W R/W R/W R/W FFDAT7 FFDAT6 FFDAT5 FFDAT4 FFDAT3 FFDAT2 FFDAT1 FFDAT0 Endpoint 0 FIFO data port Endpoint 0 FIFO is a 8 bytes FIFO. Firmware can read/write this port 8 times to get/put the FIFO data. Value on POR: "x x x x x x x x" FFDAT1 (Address 18h, Endpoint 1 FIFO port) R/W R/W R/W R/W R/W R/W R/W R/W FFDAT7 FFDAT6 FFDAT5 FFDAT4 FFDAT3 FFDAT2 FFDAT1 FFDAT0 Endpoint 1 FIFO data port Endpoint 1 FIFO is 8 bytes FIFO. Firmware can read this port 8 times to get the FIFO data. Value on POR: "x x x x x x x x" EP0RXST (Address 19h, Endpoint 0 receiving status register) R/O R/O R/O R/O RXST3 RXST2 RXST1 RXST0 RXST[3:0]: If EP0RX is set, then there's a complete transaction. RXST[3:0] indicate the packet received. Bit Value Packet received 1001 SETUP token with DATA0 packet 0101 OUT token with DATA0 packet 0110 OUT token with DATA1 packet Value on POR: "- - - - x x x x" 4.3 MCU FUNCTION REGISTERS Name INDR TIMER PCL STATUS INDAR PORT1 PORT2 PCHBUF INTEN PHVAL PHSEL DMODE INDR PSCON Function Addressing this location will use the content of INDAR to address data memory (not a physical address) Timer register Program Counter's low byte Status register Indirect address register Port 1 data register Port 2 data register Write buffer of Program Counter's bit 10-8 Interrupt enable register Photo-sensor value register Photo-sensor input select register Photo-sensor input mode register Addressing this location will use the content of INDAR to address data memory (not a physical address) Prescaler control register
Address 00h 01h 02h 03h 04h 06h 07h 0Ah 0Bh 0Dh 0Eh 0Fh 80h 81h
14
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
82h 83h 84h 86h 87h 8Ah 8Bh PCL STATUS INDAR PORT1CON PORT2CON PCHBUF INTEN Program Counter's low byte Status register Indirect address register Port 1 direction control register Port 2 direction control register Write buffer of Program Counter's bit 10-8 Interrupt enable register Table 4-2 MCU Function Register Summary
INDR (Address 00h/80h) INDR is not a physical register. Addressing INDR register will cause indirect addressing. Any instruction using the INDF register actually accesses the register pointed by the INDAR register. The indirect addressing method only can be used for general purpose registers.
TIMER (Address 01h, Timer register) R/W R/W R/W R/W R/W R/W R/W R/W TIMER7 TIMER6 TIMER5 TIMER4 TIMER3 TIMER2 TIMER1 TIMER0 The timer starts to count up after power on reset. The TMROF bit at INTEN register will be set when the TIMER register overflows from FFh to 00h. If both TMROEN and GIE bits at INTEN register are set, an interrupt will be generated when TIMER register overflows. Value on POR: "0 0 0 0 0 0 0 0" PCL (Address 02h/82h, Program Counter's low byte) R/W R/W R/W R/W PCL7 PCL6 PCL5 PCL4
R/W PCL3
R/W PCL2
R/W PCL1
R/W PCL0
The Program Counter (PC) is 11-bits wide. The low byte comes from the PCL register, which is a readable and writable register. The high byte is not directly readable or writable and comes from PCHBUF. The GL600USB has a 4 level deep x 11-bits wide hardware stake. The stake space is not part of either program or data space and the stack pointer is not readable or writable. The PC is pushed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is poped in the event of a RETIA, RETI or a RET instruction execution. PCHBUF is not affected by a push or pop operation. When write to PCL command executed, all 3 bits of PCHBUF will be loaded to PC because PCL is only a 8 bits register. Value on POR: "0 0 0 0 0 0 0 0" Status (Address 03h, Status register) R/W R/W R/W R/W BS ZO HC CA BS: Bank Select. Because only 7 bits (bit 0~bit 6) operand implied by instruction for register address, this bit is used as address bit 7 when register access. 1: Bank 1 (80h-FFh) 0: Bank 0 (00h-7Fh) ZO: Zero bit 1: The result of an arithmetic or logic operation is zero 0: The result of an arithmetic or logic operation is not zero HC: Half Carry/Borrow bit 1: Carry or not borrow from the 4th low order bit 0: Borrow or not carry from the 4th low order bit CA: Carry/Borrow bit 1: Carry or not borrow from the most significant bit 0: Borrow or not carry from the most significant bit
15
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
Value on POR: "- - 0 - - 0 0 0" INDAR: (Address 04h/84h, Indirect address register) R/W R/W R/W R/W R/W R/W R/W R/W INDAR7 INDAR6 INDAR5 INDAR4 INDAR3 INDAR2 INDAR1 INDAR0 Any instruction using the INDF register actually accesses the register pointed by the INDAR register. Value on POR: "x x x x x x x x" [1] Note 1: "x" means unknown PORT1 (Address 06h, Port 1 data register) R/W R/W R/W R/W R/W PORT1.4 PORT1.3 PORT1.2 PORT1.1 PORT1.0 PORT1 is a 5-bits latch for Port 1.0~Port 1.4. Reading the PORT1 register gets the status of the pins. Writing to it will write to the port latch. All write operations are read-modify-write operations. PORT1CON is used to enable/disable every bits of the port latch. Value on POR: "- - - x x x x x" PORT2 (Address 07h, Port 2 data register) R/W R/W R/W R/W R/W R/W R/W R/W PORT2.7 PORT2.6 PORT2.5 PORT2.4 PORT2.3 PORT2.2 PORT2.1 PORT2.0 PORT2 is an 8-bits latch for Port 2.0~Port 2.7. Reading the PORT2 register reads the status of the pins. Writing to it will write to the port latch. All write operations are read-modify-write operations. PORT2CON is used to enable/disable every bits of the port latch. Value on POR: "x x x x x x x x" PCHBUF (Address 0Ah/8Ah, Write buffer of Program Counter's bit 10-8) R/W R/W R/W PCHBUF2 PCHBUF1 PCHBUF0 Write buffer for upper 3-bits of Program Counter. The upper byte of Program Counter is not directly accessible. PCHBUF is a holding register for the PC[10:8] that are transferred to the upper byte of the Program Counter when branch occur. Please see PCL register to get more detail information. Value on POR: "- - - - - 0 0 0" INTEN (Address 0Bh/8Bh, Interrupt enable register) R/W R/W R/W GIE TMROEN TMROF GIE: Global interrupt enable bit 1: Enable all interrupts 0: Disable all interrupts TMROEN: Timer overflow interrupt enable bit 1: Enable timer interrupt 0: Disable timer interrupt TMROF: Timer overflow interrupt flag bit. This bit should be cleared to `0' by firmware after it is set by hardware. 1: Timer register has overflowed 0: Timer register did not overflow Value on POR: "0 - 0 - - 0 - -" PHVAL (Address 0Dh, Photo-sensor value register) R/O R/O R/O R/O PHVAL3 PHVAL2 PHVAL1 PHVAL0 PHVAL[3:0]: the 8 channel, 4 bits analog-to-digital converter data. The ADC input is select by PHSEL register from Port 2.0~Port 2.7
16
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
Bit Value Analog value 0000 0 V - 5/16 V 0001 5/16 V - 5/8 V 0010 5/8 V - 15/16 V 0011 15/16 V - 5/4 V 0100 5/4 V - 25/16 V 0101 25/16 V - 15/8 V 0110 15/8 V - 35/16 V 0111 35/16 V - 5/2 V 1000 5/2 V - 45/16 V 1001 45/16 V - 25/8 V 1010 25/8 V - 55/16 V 1011 55/16 V - 15/4 V 1100 15/4 V - 65/16 V 1101 65/16 V - 75/16 V 1110 75/16 V - 5V 1111 5V Value on POR: "- - - - x x x x" PHSEL (Address 0Eh, Photo-sensor analog input select register) R/W PHSEL2 PHSEL[2:0]: The selection register for 8 channel 4 bits, ADC. Bit Value Source pin of the ADC 000 PORT2.0 001 PORT2.1 010 PORT2.2 011 PORT2.3 100 PORT2.4 101 PORT2.5 110 PORT2.6 111 PORT2.7 Value on POR: "- - - - - x x x" DMODE (Address 0Fh, Photo-sensor input mode register) R/W R/W R/W R/W R/W R/W R/W R/W DMODE7 DMODE6 DMODE5 DMODE4 DMODE3 DMODE2 DMODE1 DMODE0 DMODE[7:0]: Individual enabler for Port 2.7~Port 2.0 input buffer. 1: Indicate the corresponding pin on Port 2 can be used in input mode. This pin can be selected with PHSEL and firmware can get its state from PHVAL also. 0: Indicate the corresponding pin on Port 2 cannot be used in input mode. But even firmware cannot read this pin directly from Port 2 directly, this pin can be selected with PHSEL and firmware can get its state from PHVAL also. Value on POR: "0 0 0 0 0 0 0 0" PSCON (Address 81h, Prescaler control register) R/W PSDIS R/W PS2 R/W PS1 R/W PS0 R/W PHSEL1 R/W PHSEL0
PSDIS: Prescaler disable bit 1: Set prescaler disable 0: Set prescaler enable PS[2:0]: Prescaler rate select bits. These bits are used to control timer speed. The following table means that how many instruction cycles the TIMER register should be added by 1 when PSDIS = 0.
17
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
Timer Rate (PSDIS = 0) 000 1:2 001 1:4 010 1:8 011 1:16 100 1:32 101 1:64 110 1:128 111 1:256 Value on POR: "- - - - 1 1 1 1" PORT1CON (Address 86h, Port 1 direction control register) R/W R/W R/W R/W R/W P1CON4 P1CON3 P1CON2 P1CON1 P1CON0 There is a data direction control bit to match every pin of Port 1. The direction control bits can configure these pins as output or input. Setting a PORT1CON register bit put the corresponding output driver in a hiimpedance mode. Clearing a bit in the PORT1CON register puts the contents of the output latch on the selected pin. Value on POR: "- - - 1 1 1 1 1" PORT2CON (Address 87h, Port 2 direction control register) R/W R/W R/W R/W R/W R/W R/W R/W P2CON7 P2CON6 P2CON5 P2CON4 P2CON3 P2CON2 P2CON1 P2CON0 There is a data direction control bit to match every pin of Port 2. The direction control bits can configure these pins as output or input. Setting a PORT2CON register bit put the corresponding output driver in a hiimpedance mode. Clearing a bit in the PORT2CON register puts the contents of the output latch on the selected pin. Value on POR: "1 1 1 1 1 1 1 1"
Bit Value
4.4
FULL-RANGE DETECTION AND ANALOG-TO-DIGITAL CONVERTER
The GL600USB provides the unique "Full-Range Detection" ability. Over 95% of PC mouse market adopts photo-sensor system to detect the mechanical movement of the roller inside the mouse. Because the sensors may have varied characteristic on their output DC voltage level and output moving range, the mouse manufacturers can't avoid the expensive process of matching LED and photo-sensor. By providing those photo-input pins with full-range detection function, the mouse makers can ignore the range difference between those sensors, so the manufacturing procedure is simple and a huge cost is saved on the manufacturing line. By detecting the output signal came from the sensors, Genesys Logic's patented algorithm could learn the tiny difference of every signal and automatically adjust the threshold for the sensors without any side effect. This new outstanding design can help the manufacturers decrease their inconvenience on mass -production line and cut their human and mechanical cost tremendously. There's a 4-bit Analog-to-Digital Converter (ADC) module in the GL600USB. The input signal of ADC can be connected to Port 2.0 ~ Port 2.7. When these I/O pins is used for analog input, the corresponding bits in DMODE register should be set to 0 to disable input buffer of Port 2. This can save power consumed by the pad of Port 2. The PHSEL register is used to select which input connected to the ADC and the PHVAL register is used to store the digital value converted by the ADC. The Genesys Logic's proprietary
18
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
algorithm can detect any analog waveform from photo-sensor with amplitude larger than 1V. The ADC is a high-speed converter. It takes less than 500ns to complete the conversion. Because GL600USB is running at 3 MIPS for USB low speed application, only two dummy instructions should be added between write PHSEL to read PHVAL.
4.5
GENERAL PURPOSE I/O PORTS
Interface with peripherals is conducted via up to 13 GPIO signals. These 13 signals are divided into two ports: Port 1 and Port 2. Port 1 contains five lines (PORT1.0-PORT1.4) and Port 2 contains eight lines (PORT2.0-PORT2.7). The Port 1 data register is located at data memory address 06h while the Port 2 data register is located at data memory address 07h. Port 2 is a low current port with analog input capability suitable for connecting photo-sensor. Port 1 is a high current port capable of LED drive. Each GPIO line may include an internal pull-up or pull-down resistor. Port 2's internal pull-down resistor value can be programmed by option-code. Each output drive has slew-rate control to reduce EMI. Please see the following table for details. Driving capability Pull-up resistor Pull-down resistor PORT1.0 20 mA PORT1.1 20 mA PORT1.2 4 mA 10K PORT1.3 4 mA 10K PORT1.4 4 mA 10K PORT2.0 4 mA 4K/8K/16K/32K [1] PORT2.1 4 mA 4K/8K/16K/32K PORT2.2 4 mA 4K/8K/16K/32K PORT2.3 4 mA 4K/8K/16K/32K PORT2.4 4 mA 4K/8K/16K/32K PORT2.5 4 mA 4K/8K/16K/32K PORT2.6 4 mA 4K/8K/16K/32K PORT2.7 4 mA 4K/8K/16K/32K Note 1: The pull-down resistor can be configured as 4K, 8K, 16K or 32K by option-code. Table 4-3 General Purpose I/O Port Summary 4.6 TIMER INTERRUPT
The Timer Interrupt is generated when the TIMER register overflows from FFh to 00h. This overflow sets bit TMROF (INTEN<2>). The interrupt can be masked by clearing bit TMROEN (INTEN<5>). Bit TMROF must be cleared in software by the Timer module interrupt service routine otherwise the Timer Interrupt will not be generated again. If prescaler is disabled, the timer register will increase every instruction cycle. If prescaler is enabled, its increment cycle depends on PS0~PS2 bits in PSCON register. 4.7 USB ENGINE
The USB module contains three functional blocks: a 3.3-volt regulator, a low-speed USB transceiver, and the Serial Interface Engine (SIE). The following details the function of the regulator, transceiver, and SIE. 4.7.1 Voltage Regulator
The USB data lines are required by the USB specification to have a maximum output voltage between 2.8V and 3.6V. Because the GL600USB is a low speed USB device, the D- lines also are required to have an
19
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
external 1.5-k pull-up resistor connected between a data line and a voltage source between 3.0 V and 3.6 V. Since the power provided by the USB cable is specified to be between 4.4V and 5.0V, an on-chip regulator is used to drop the voltage to the appropriate level for sourcing the USB transceiver and external pull-up resistor. An output pin driven by the regulator is provided to source the 1.5-k external resistor. 4.7.2 USB Transceiver
The USB transceiver provides the physical interface to the USB D+ and D- data lines. The transceiver is composed of two parts: an output driver circuit and a receiver. The USB transceiver uses a differential output driver to driver the USB data signal onto the USB cable. The static output swing of the driver in its low state is below the VOL of 0.3V with 1.5-k load to 3.6V and in its high state is above the VOH of 2.8V with 15-k load to ground. The output swings between the differential high and low state are well balanced to minimize signal skew. Slew rate control on the driver is used to minimize the radiated noise and cross talk. The driver's outputs support 3-state operation to achieve bi-directional half-duplex operation. The driver can tolerate a voltage on the signal pins of -0.5V to 3.8V with respect to local ground reference without damage. The rise and fall time of the signals on this cable are greater than 75ns to keep RFI (radio frequency interference) emissions under FCC (Federal Communications Commission) class B limits and less than 300ns to limit timing delays, signaling skews, and distortions. The driver reaches the specified static signal levels with smooth rise and fall times, and minimal reflections and ringing when driving the cable. This driver is used only on segments between low-speed devices and the ports to which they are connected. USB data transmission is done with differential signals. A differential input receiver is used to accept the USB data signal. A differential 1 on the bus is represented by D+ being at least 200mV more positive than D- as seen at the receiver, and a differential 0 is represented by D- being at least 200mV more positive than D+ as seen at the receiver. The signal cross over point must be between 1.3V and 2.0V. The receiver features an input sensitivity of 200mV when both differential data inputs are in the range of 0.8V and 2.5V with respect to the local ground reference. This is called the common mode input voltage range. Proper data reception also is achieved when the differential data lines are outside the common mode range. The receiver can tolerate static input voltage between -0.5V to 3.8V with respect to its local ground reference without damage. In addition to the differential receiver, there is a single-ended receiver for each of the two data lines.
1.0
Minimum Differential Sensitivity (volts)
0.8
0.6
0.4
0.2
0.0 0.0 0.2 0.4
0.6 0.8 1.0
1.2 1.4
1.6 1.8 2.0
2.2 2.4 2.6
2.8 3.0 3.2
Common Mode Input Voltage (volts)
Figure 4-3 Differential Input Sensitivity over Entire Common Mode Range
20
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
The data receivers for all types of devices must be able to properly decode the differential data in the presence of jitter. The more of the bit time that any data edge can occupy and still be decoded, the more reliable the data transfer will be. Data receivers are required to decode differential data transitions that occur in a window plus and minus a nominal quarter bit time from the nominal (centered) data edge position. Jitter will be caused by the delay mismatches and by mismatches in the source and destination data rates (frequencies).
TPERIOD Differential Data Lines
TJR TJR1 TJR2
Consecutive Transitions N * TPERIOD + TJR1 Paired Transitions N * TPERIOD + TJR2
Figure 4-4 Receiver Jitter Tolerance
The source of data can have some variation (jitter) in the timing of edges of the data transmitted. The time between any set of data transitions is N*TPeriod jitter time, where N is the number of bits between the transitions and T Period is defined as the actual period of the data rate. The data jitter is measured with the same capacitive load used for maximum rise and fall times and is measured at the crossover points of the data lines. For low-speed transmissions, the jitter time for any consecutive differential data transitions must be within 25ns and within 10ns for any set of paired differential data transitions. These jitter numbers include timing variations due to differential buffer delay, rise/fall time mismatches, internal clock source jitter, noise and other random effects. The output rise time and fall time are measured between 10% and 90% of the signal. Edge transition time for the rising and falling edges of low-speed signals is 75ns (minimum) into a capacitive load (CL ) of 50pF and 300ns (maximum) into a capacitive load of 350pF. The rising and falling edges should be transitioning (monotonic) smoothly when driving the cable to avoid excessive EMI.
Rise Time CL Differential Data Lines 10% CL Full Speed: 4 to 20ns at CL = 50pF 90% 90% 10% Fall Time
tR
tF
Low Speed: 75ns at CL = 50pF, 300ns at CL = 350pF
21
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
Figure 4-5 Data Signal Rise and Fall Time
4.7.3
Serial Interface Engine (SIE)
The SIE manages data movement between the CPU and the transceiver. The SIE handles both transmit and receive operations on the USB. It contains the logic used to manipulate the transceiver and the endpoint registers. The byte count buffer is loaded from TXCNT(TXCTL0<3~0>) during endpoint 0 transmit operations. This same buffer is used for receive transactions to count the number of bytes received at endpoint 0 and, upon the end of transaction, transfer the value to RXCNT(RXCTL0<3~0>). When transmitting, the SIE handles parallel-to-serial conversion, CRC generation, NRZI encoding, and bit stuffing. When receiving, the SIE handles sync detection, packet identification, end-of-packet detection, bit (un)stuffing, NRZI decoding, CRC validation, and serial-to-parallel conversion. Errors detected by the SIE include bad CRC, timeout while waiting for EOP, and bit stuffing violations. All USB devices are required to have an endpoint 0 that is used to initialize and manipulate the device. Endpoint 0 provides access to the device's configuration information and allows generic USB status and control accesses. Endpoint 0 can receive and transmit data. Both receive and transmit data share the same 8-byte Endpoint 0 FIFO, FFDAT0. Received data may overwrite the data previously in the FIFO. Endpoint 1 is of transmit only. This endpoint is used to transmit HID report data to host.
4.8 4.8.1 Field r A i b 4.8.2
INSTRUCTION SET SUMMARY Operand Field Descriptions Description Register address Accumulator Immediate data Bit address within a 8-bit register Instruction Set Description Cycles Flags Affected CA, HC, ZO CA, HC, ZO CA, HC, ZO ZO ZO
Mnemonic, Operands Arithmetic Operations ADDAR r, A ADDAR A, r ADDAI i INCR r INCR A, r INCRSZ r INCRSZ A, r SUBAR r, A SUBAR A, r SUBIA i
Add r and A, r <- r + A Add A and r, A <- A + r Add A and i, A <- A + i Increment r, r <- r +1 Increment r, A <- r + 1 Increment r, r <- r +1, skip if (r = 0) Increment r, A <- r +1, skip if (A = 0) Subtract A from r, r <- r - A Subtract A from r, A <- r - A Subtract A from i, A <- i - A
1 1 1 1 1 1 or 2 1 or 2 1 1 1
CA, HC, ZO CA, HC, ZO CA, HC, ZO
22
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
DECR r Decrement r, r <- r -1 DECR A, r Decrement r, A <- r -1 DECRSZ r Decrement r, r <- r-1, skip if (r = 0) DECRSZ A, r Decrement r, A <- r - 1, skip if (A = 0) CLRR r Clear r, r <- 0 CLRA Clear A, A <- 0 NOP No operation Logical Operations ANDAR r, A And r and A, r <- r & A ANDAR A, r And A and r, A <- A & r ANDAI i And A and i, A <- A & i CMPR r Complement r, r <- r ^ FF CMPR A, r Complement r, A <- r ^ FF ORAR r, A Inclusive OR r with A, r <- r | A ORAR A, r Inclusive OR A with r, A <- A | r ORIA i Inclusive OR i with A, A <- A | i XORAR r, A Exclusive OR r with A, r <- r ^ A XORAR A, r Exclusive OR A with r, A <- A ^ r XORIA i Exclusive OR i with A, A <- A ^ i Bit-wise Operations BCR r, b Bit clear r, r.b <- 0 BSR r, b Bit set r, r.b <- 1 BTRSC r, b Bit test r, skip if (r.b = 0) BTRSS r, b Bit test r, skip if (r.b =1) Data Movement Operations MOV r, A Move A into r, r <- A MOV A, r Move r into A, A <- r MOVIA i Move i into A, A <- i Shift Operations SWAPR r Swap high and low nibbles in r SWAPR A, r Swap high and low nibbles in r, result put into A RLR r Rotate r left through C RLR A, r Rotate r left through C, (C, A) <- (r, C) RRR r Rotate r right through C RRR A, r Rotate r right through C, (A, C) <- (C, r) Control Transfer Operations CALL i Call subroutine JUMP i Jump to address RETIA Return and load i to A RETI Return from interrupt RET Return from subroutine 1 1 1 or 2 1 or 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 or 2 1 or 2 1 1 1 1 1 1 1 1 1 2 2 2 2 2 CA CA CA CA ZO ZO
ZO ZO
ZO ZO ZO ZO ZO ZO ZO ZO ZO ZO ZO
ZO
23
06/19/2000
Revision 1.3
5
5.1
Firmware Programming Guide
GL600USB/GL600USB-A/GL600USB-B
USB Power On Reset and Bus Reset Initialization
Power on reset USB reset (Address 0)
No
TXSE0 = 1
Yes
Power on reset detected USB reset detected Wait host controller to initialize the USB device Drive SE0 on USB about 300 ms Clear SE0 bit and Wait for USB reset
24
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.2
Suspend/Resume/Wakeup
SUSPD
=
1
W
rite '1' to clear SUSPD
Set PWRDN bit to enter power down mode W a it for resume or wakeup
No No
RESUME
=
1
Yes
Check remote wakeup event like mouse button pressed or mouse moved
W
rite '1' to clear RESUME
Remote wakeup event occur ?
Suspend & wakeup process complete
Yes
S e t W A K E b it to drive 'K' state on USB
Delay about 1 ms to clear WAKE bit
25
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.3
Receive Packet via Endpoint 0
EP0RX = 1 Packet received complete
Write '1' to clear EP0RX bit
Get received byte count from RXCNT of FFCNT0 register
Read received data continuous from FFDAT0 (total RXCNT bytes)
Clear RXDIS0 bit to enable endpoint 0 receiver
Yes
RXST = (1, 0, 0, 1)
No
SETUP data packet received complete
OUT data packet received complete
26
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.4
Transmit Packet via Endpoint 0
Start to transmit function
Set FFRST0 to reset FIFO
Push all transmitting data into FFDAT0 (maximum 8 bytes)
Set correct data toggle sequence via TXSEQ0 and Set transmit data length into TXCNT at FFCNT0
Set TXOE0 bit SIE will transmit the packet while it receives a IN token
27
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.5 Transmit Packet via Endpoint 1
Start to transmit function
Set FFRST1 to reset FIFO
Push all transmitting data into FFDAT1 (maximum bytes) 8
Set correct data toggle sequence and Set transmit data length into TXCNT in FFCNT1 via TXSEQ1
Set TXOE1 bit SIE will transmit the packet while it receives a IN token
28
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.6
Timer Interrupt Because CPU may enter timer interrupt routine at any time, the timer interrupt routine should backup all special registers at its entry point and restore them before return. (Address 0x004) TIMER_ENTRY:
MOV SWAPR BCR MOV MOV MOV
A_TEMP, A A, STATUS STATUS, BS S_TEMP, A A, INDAR I_TEMP, A
; ; Execute interrupt service routine ; MOV MOV SWAPR MOV SWAPR SWAPR BCR RETI 5.7 Conditional Branch
A, I_TEMP INDAR, A A, S_TEMP STATUS, A A_TEMP A, A_TEMP INTEN, TMROF
Example: Conditional branch can be according to value of Accumulator. Firmware can use this method to return value for lookahead table. Because Accumulator is only 8 bits wide, the higher 3 bits of Program Counter should be load into PCHBUF before the conditional branch executed. (Address 0x540) LOOKAHEAD:
MOVIA MOV MOVIA ADDAR RETIA RETIA RETIA . . .
0x05 PCHBUF, A LOOKAHEAD_VAL PCL, A 0 ; Acc = 0 1 ; Acc = 1 2 ; Acc = 2 . . .
5.8
Change Register Bank Usually keeps BS = 0. If firmware want to access register address 0x80 to 0x8F, set BS = 1. After process register address 0x80 to 0x8F complete, clear BS = 0 to address 0x00 to 0x7F. BSR MOV BCR STATUS, BS PORT1CON, A STATUS, BS
29
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
5.9
Read Photo Sensor Input
Start to Read Photo Sensor
Select 1 of 8 channels by write 0~7 to PHSEL register
Add two dummy instructions to delay 667 us
Get phtot sensor voltage value from PHVAL register
30
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
6
ABSOLUTE MAXIMUM RATINGS
Maximum ratings are the extreme limits to which the micro-controller can be exposed without permanently damaging it. The micro-controller contains circuitry to protect the inputs against damage from high static voltages; however, do not apply voltages higher than those shown in the table. Keep VIN and VOUT within the range GND (VIN or VOUT) VCC. Connect unused inputs to the appropriate voltage level, either GND or VDD . Symbol TSTG TOP VCC VIN I IMGND IMVCC VESD Characteristic Storage temperature Operating temperature Supply voltage DC input voltage Maximum current per pin excluding VDD and VSS Maximum current out of GND Maximum current out of VCC Static discharge voltage Value -55 to +150 0 to +70 -0.5 to +7.0 -0.5 to +VDD + 0.5 25 100 100 >4000 Unit C C V V mA mA mA V
7
ELECTRICAL CHARACTERISTICS
Conditions
FOSC = 6MHz; Operating Temperature = 0 to 85C; VCC = 4.4 to 5.5V Symbol Characteristic Min Max Units General ICC Operating supply current 20 mA ISB Supply current - suspend 300 A mode USB Interface VOH Static output high 2.8 3.6 V VOL Static output low 0.3 V VDI Differential input 0.2 V sensitivity VCM Differential common mode 0.8 2.5 V range VSE Single ended receiver 0.8 2.0 V threshold ILO Hi-Z state data line leakage -10 +10 V V3.3 Regulator supply voltage 3.0 3.6 V GPIO Interface RUP PORT2.2-4 pull-up 68 120 K resistance RDOWN PORT1.0-7 pull-down 4 32 K resistance VOH1 Static output high for 2.4 V PORT1.2-4, PORT2.0-7 VOL1 Static output low for 0.4 V PORT1.2-4, PORT2.0-7 VOH2 Static output high for 2.4 V PORT1.0-1 VOL2 Static output low for 0.4 V PORT1.0-1
See note 1
RL of 15K to GND RL of 15K to V3.3 |(D+) - (D-)| Include VDI range
0V < VIN < 3.3V IL = 4mA
Code option VCC = 5V; IOH = 4mA VCC = 5V; IOL = 4mA VCC = 5V; IOH = 20mA VCC = 5V; IOL = 20mA
31
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
VIH VIL ISINK1 ISINK2 IIN fOP Static input high Static input low Sink current for PORT1.24, PORT2.0-7 Sink current for PORT1.01 Input leakage current USB Low-speed Source Internal operating frequency Transition time Rise time Fall time Rise/Fall time matching Output signal crossover voltage Low speed data rate Source differential driver jitter To next transition For paired transition Receiver data jitter tolerance To next transition For paired transition Source EOP width Differential to EOP transition skew Receiver EOP width Must reject as EOP Must accept 2.0 0.9 4 20 -1 1.5 +1 1.5 V V mA mA A MHz VCC = 5V VCC = 5V VOUT = 0.4V; VOUT = 0.4V; VOUT = 0V or VCC
tR tF tRFM VCRS tDRATE
75 300 75 80 1.3 1.4775 676.8 300 120 2.0 1.5225 666.0
ns ns ns ns % V Mbs ns
CL = 50pF CL = 350pF CL = 50pF CL = 350pF tR / t F 1.5Mbs 1.5%
tUDJ1 tUDJ2
-25 -10
25 10
ns ns
CL = 350pF measured at crossover point
tDJR1 tDJR2 tEOPT tDEOP
-75 -45 1.25 -40
75 45 1.50 100
ns ns s ns
CL = 350pF measured at crossover point Measured at crossover point Measured at crossover point
tEOPR1 tEOPR2 Notes:
330 675
ns ns
Measured at crossover point
1. ISB measured with USB in suspend mode; using external square wave clock source (FOSC = 6MHz); transceiver pull-up resistor of 1.5K between V3.3 and D- and 1.5K termination resistors on D+ and D- pins; no port pins sourcing current. The ISB value is including power consumed by external resistors.
32
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8
8.1
PACKAGE DIAGRAMS
16-pin P-DIP
D 15" (2X)
F E1 C A1 A
5" (2X)
e
L1 L B B1 15' (4X) eB
Symbol
A A1 B B1 C D E1 F L L1 e EB
Dimension in mil
Min -59 ---740 259 290 ---345 4 Nom 130 60 18 60 10 750 260 300 130 20 100 355 5.5 Max -61 ---760 -310 ---365 7 Min -1.499 ---18.796 6.579 7.366 ---8.763 4
Dimension in mm Nom 3.302 1.524 0.457 1.524 0.254 19.050 6.604 7.620 3.302 0.508 2.540 9.017 5.5 Max -1.549 ---19.304 -7.874 ---9.271 7
Figure 8-1 Package outline dimension for 16-pin P-DIP
33
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8.2
18-pin P-DIP
D 15"(2X ) L1 A1 L A F E1 C
e
B B1
15"(4X) eB
c
Symbol
A A1 B B1 C D E1 F L L1 1 e1 eB
Dimension in mils
Dimension in mils
Min
-59 ---890 259 290 ---345 4
Nom Max
130 60 18 60 10 900 260 300 130 20 100 355 5.5
Min
Nom Max
--3.302 -61 1.499 1.524 1.549 --0.457 ---1.524 ---0.254 -910 22.606 22.860 23.114 -6.579 6.604 -310 7.366 7.620 7.874 --3.302 ---0.508 ---2.540 -365 8.763 9.017 9.271 7 4 5.5 7
Figure 8-2 Package outline dimension for 18-pin P-DIP
34
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8.3
20-pin P-DIP
E1
F A1 A C
e
c
B B1 D
eB
Symbol
A A1 B B1 C D E1 F e eB
Dimension in mil
Min -59 ---1015 259 290 -345 4 Nom 130 60 18 60 10 1025 260 300 100 355 5.5 Max -61 ---1035 -310 -365 7
Dimension in mm Min Nom -3.302 1.499 1.524 ---25.781 6.579 7.366 -8.763 4 0.457 1.524 0.254 26.035 6.604 7.620 2.540 9.017 5.5
Max -1.549 ---26.289 -7.874 -9.271 7
Figure 8-3 Package outline dimension for 20-pin P-DIP
35
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8.4 16-pin SOP
A2
B
D
e
A 1 E1
A
C
L e B
Symbol
A A1 A2 B C D E1 e eB L
Dimension in mils Min Nom Max --58 --6 ------24 ----16 ----8 --388 390 392 152 154 156 --50 ----238 --25 ----0 3 6
Dimension in mm Min --0.152 ------9.855 3.861 ----0.635 0 Nom 1.473 --0.610 0.406 0.203 9.906 3.912 1.270 6.045 --3 Max ----------9.957 3.962 ------6
Figure 8-4 Package outline dimension for 16-pin SOP
36
06/19/2000
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8.5 18-pin SOP
00 6 y .1tp
00 0 y .5tp
D
A
S A I GP A E E TN LN
00 4 m x .0 o
SYMBOLS A A1 D E H L
MIN 0.093 0.004 0.447 0.291 0.394 0.016 0
MAX 0.104 0.012 0.463 0.299 0.419 0.050 8
A1
Figure 8-5 Package outline dimension for 18-pin SOP
37
06/19/2000
0.020 X 45
L
H
E
Revision 1.3
GL600USB/GL600USB-A/GL600USB-B
8.6 20-pin SOP
00 6 y .1tp
00 0 y .5tp
D
A
S A I GP A E E TN LN
00 4m x .0 a
A1
SYMBOLS A A1 D E H L
MIN 0.093 0.004 0.496 0.291 0.394 0.016 0
MAX 0.104 0.012 0.508 0.299 0.419 0.050 8
Figure 8-6 Package outline dimension for 20-pin SOP
0.020 X 45
L
H
E
38
06/19/2000
Revision 1.3

▲Up To Search▲

Price & Availability of GL600USB-A

	To Download GL600USB-A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .